Hello, Any experienced professionals who would like guide some newbies like myself to the audio engineering world?
Community discussionParticipant 065#1
By Skill/Experience Level
16 readable posts · Team contributions are labelled separately from community replies.
Hello, Any experienced professionals who would like guide some newbies like myself to the audio engineering world?
Hi [participant mention] [link withheld], I'd be glad to help you out with any questions you may have -- what are you thinking of specifically?
Well, one would be how much compression to add to a recording, and when to know where the acceptable levels are. As well as in equeing, like knowing when to add more bass than treble and vice versa. Also the mids Im not sure what to do with those mid frequencies.
[participant mention] [link withheld] first, you should research a bit about compression, how it works and all that. The common element among all kinds of compression is gain reduction, so you're turning down the signal as though you were moving a fader. So, you don't usually want to be severe with it unless you're treating it more like an effect. I'd suggest no more than 4-6 db of gain reduction from a compressor if you're using it while recording or in a live situation on something like drums, which have real loud transients -- even less for other instruments that have a more proportional attack. Afterwards, when you're in the mixing stage, some more compression could be used with maybe some more gain reduction -- ultimately there's a lot of compression that happens little bits at a time throughout the process, so like I said it's best to be conservative with it. EQ is mostly a question of taste, but again it's best to be conservative because a little bit can go a long way and too much will definitely be a problem. EQ will definitely be covered in this course, so stay tuned.
Willing to help where I can.
Broadcasting, recording, playing, etc.
As far as how much compression or what kind of eq to use, it matters much with the equipment.
I used the included plugins in Logic and got very suitable results. Then I got a Universal Audio Apollo, and hooked up the plugins for the Pultec EQP-1 and the Teletronix LA-2A on my wife's voice, and OMG!, she sounded totally new and luscious!
Post processing isn't there to make music sound more natural, it's there to make it sound awesome (different than when your microphone originally picked it up.)
(I don't work for uaudio.com, but check out the Universal Audio Apollo. It's nearly impossible to do something wrong with it. It may seem a little expensive, but believe me, it's cheap for what you get!)
I hope this helps.
What are the "M" the "S" the "PFL" button on our mixer tool, and what does the knob do?
oh wait, ok, so M is mono, S is stereo, still not sure whar pfl and the knob are doing there.
Oh! Thank goodness for this! I cannot work the site let alone understand what I am supposed to do... but I am still VERY keen! I wonder if anyone has a link or a diagram of a basic mixing desk identified and explained? That would be so very useful... Yes folks... that is the level I am working at... but... that will change... Please help a little!! ?? Image omitted from this public edition
[participant mention] [link withheld], where did you even find the mixer tool? You're way ahead, so far as I can tell that will not come into play until week 3. But, the M stands for mute, the S for solo, PFL for pre-fader listen, and the knob is for panning. Last time around, the PFL button didn't work on the PWYM mixer, so it did nothing. This will all be explained in due time.
[participant mention] [link withheld], check out the wikipedia article on mixing consoles [link withheld] , especially the area under "channel input strip." Basically, you have strips that run down the console (toward and away from you, if you're in front of it) -- each of these strips deals with a single input. First, furthest knob away from you, you have the preamp where you apply gain to the signal -- this is for calibrating the microphone volume to match the signal. After that, different things can happen but usually you'll have an EQ section with some knobs for adjusting the highs, mids, and lows etc (the details depend on the specific desk). Getting closer to you, there may also be knobs for aux sends, this is for sending the signal to a variety of auxiliary outputs (could be used for monitors, or outputs to another piece of hardware). Again this varies greatly from desk to desk depending on the complexity. There may be a section after that where you can also send the signal to "groups" or the master buss (main output), usually these are buttons or switches. There is usually the panning knob here for sending the strip to the left or right of the master, or for panning them to different groups. Finally, you have the fader, the slider you can use to adjust the volume of the signal coming out of the strip (after the preamp). The PFL button is for listening to the sound of the strip before the fader, so you can hear the pure sound of the preamp before the fader comes into play. Some of the aux sends may be pre-fader as well, but groups and busses are usually post-fader (so you can mix the different strips into a group using the faders). After all these strips, usually towards the right, there may be faders and knobs to control the overall levels of the aux sends, groups or busses, and master faders. Sometimes there's master EQ and a wide variety of other routing knobs, buttons, and faders.
Thank you very much... I am going to the wiki right now! I get the impression that it is all very individualised according to the demands of a track and the foibles of the person mixing! Even this is new news to me... but does make so much sense. Image omitted from this public edition
[participant mention] [link withheld], it was in the Getting Started>Interview with Kevin and Jerry page after "refamiliarize yourself with Sledgehammer and In Your Eyes". But, I see that it's not there anymore... thanks for the info...
[participant mention] [link withheld] I haven't even looked in there, but I was going by what they have on the curriculum page. This website is a little confusing to me. I found the Sledgehammer one here [link withheld] it was in there amongst the posts you mentioned. But as I said before, M is for mute and S is for solo, the knob is for panning (left and right). So you're looking at two channel strips, a left one and a right one.
[participant mention] [link withheld], i'm thinkin the curriculum page is just a syllabus of sorts, I don't understand why they don't just put links to things in there. I am just going to look for the "module" prompts in the Community thing.... I haven't even looked in "Artist Content" and "Share" ... ok, thanks again for your descriptions, I am happy to report they make sense! Growing up with a sound engineer, I suppose some of this will all just come back to me...
Hey [participant mention] [link withheld], let me add my name to the list of pros who would be happy to help you out. Note that many of your questions will be answered in the coming weeks of the course, so hang in. You especially want to watch the videos by Alex Case, who focuses specifically on the use of effects like compression, EQ and reverb. And [participant mention] [link withheld], we're rolling out content module-by-module rather than all at once so as not to overwhelm people. Rest assured that by the end of the course, the curriculum page will be a complete set of links to all of the content, and it will stay that way going forward.
[participant mention] [link withheld], cool, I dig it. I know I could easily get overwhelmed by all of this, so far I'm having a great time!
Sure thing, thanks! il continue to ask when i'm stuck.